| Model: 999-9916-000W Specifications |
| Description |
RoboSHOT 30 QDVI System, White |
| Image Device |
1/2.8-Type Exmor CMOS Sensor |
| Video Resolution/Frequencies |
1080p60/59.94/50/30/25, 1080i/60/59.94i/50, 720p/60/59.94/50/30/25 |
| Vaddio Special Features |
Tri-Synchronous Motion: Concurrent PTZ motor movement and simultaneous PTZ arrival at a stored preset
Advanced ISP: Vivid and accurate color reproduction with extremely fast, razor sharp automatic focus and iris routines |
| Video Aspect Ratio |
16:9 Aspect Ratio for all resolutions |
| Effective Pixels |
2.14 Million Effective pixels
2.38 Million Total Pixels |
| Lens and Horizontal FOV |
30X Optical Zoom
65° (wide end) to 2.3° (tele end), F1.6 to F4.7 |
| Minimum illumination |
1.4 lx (F1.6, 50IRE), recommended illumination >100 lux and <100,000 lux |
| Minimum working distance |
10mm (wide), 1.2m (tele) |
| S/N ratio |
More than 50 dB |
| Sync system |
Internal |
| White balance |
Auto, ATW, Indoor, Outdoor, One-push, Manual (accessible through external control) |
| Gain |
Auto / Manual (0 to 28 steps - accessible through external control) |
| Back-light compensation |
On/Off (IR Remote) |
| Focusing system |
Auto Focus / Manual Focus Mode / One Push Trigger Mode / Infinity Mode / Near Limit Mode |
| Noise Reduction |
On/Off, 6 Steps, Off through 5 (accessible through external control) |
| Aperture/Detail |
16 Steps (accessible through external control) |
| Control Interface(s) |
RS-232 API: Modified VISCA Emulation (TTL signal level), Baud rate: 9600 bps and 38,400 bps, 1-Stop bit. Default to 9.6 Kb/s for Cat-5e Distance
Telnet Serial Command API
Internal Web page for Network Set-up, firmware updates and network management
Vaddio IR Remote Commander |
| Pan & Tilt Angle/Speed Pan/Tilt Angles |
±160°, Tilt: +90°, -30°
Pan/Tilt Speeds: Both Axes 0.35°/sec to 120°/sec |
| Rear Panel Connectors |
Network: RJ-45 with Green & Yellow LED to show connection and usage
RS-232: RJ-45, Carries bidirectional control to and from the camera
EZ Power Video: RJ-45 Shielded, carries power and differential video signals for the Quick-Connect Cat-5 systems |
| Rear Panel Controls |
16-Position Rotary Switch for Resolution selection
8-Position Dip Switch for IR Frequency, Image Flip, wide mode and Reset to Default Settings |
| Power Supply |
Powered by Quick-Connect interfaces |
| Compatible Joystick and Video Control Consoles |
ProductionVIEW Precision Camera Controller
ProductionVIEW HD
ProductionVIEW HD MV with Integrated Multi-viewer,
ProductionVIEW HD-SDI MV with Integrated Multi-viewer
AV Bridge MATRIX PRO |
| Operating/Storage Temperature/Humidity |
0°C (32°F) to 40°C (104°F), 20% to 80% |
| Mass |
4.85 lbs.(2.1999235643 kg) |
| Dimensions |
Small (3 dimensions not counting space/time)
6.942” (176.3mm) H x 7.056” (179.2 mm) W x 6.757” (171.6mm) D |
| Quick-Connect DVI/HDMI SR |
| Quick-Connect System |
Quick-Connect DVI/HDMI (two Cat-5e) for distances up to 100’ (30.84m)
HDMI or DVI-D and Analog Component YPbPr output with IR forwarding |
| Connectors |
Power Connector: 5.5mm OD, 2.5mm ID coaxial connector
RJ-45: Four (4) Control IN, Control OUT, Daisy Chain OUT, EZCamera Power Video Port
Video Output: DE-15 connector for HD Analog Component (Y,PB,PR) video only (No SD Support)
IR Output: Transmits modulated or non-modulated IR signals received from the HD-19 IR receiver
Video Outputs: DVI-D (Female - Single Link) or HDMI with adapter cable (using the Recessed Color Space Conversion Switch) , DE-15F (High Density D-Sub 15-Pin F) for HD YPbPr |
| Cat-5 Cable Distance |
Up to 100’ (30.5m) |
| Power Supply |
24 VDC, 2.0 Amp Switching Power Supply |
| Dimensions/Weight |
1.6” (40.64mm ) H x 8” (203.2mm) W x 6.751” (171.45mm) D, ½-Rack Size / 1.21 lbs. (0.548846804 kg) |
| Accessory |
1-RU Rack Mount Panel for two (2) units (side by side): P/N: 998-6000-003
1m (3.3’) DVI-D Male to HDMI Male P/N: 440-5643-001
3m (10’) DVI-D Male to HDMI Male P/N: 440-5643-003 |