| Model: TPRO-TXWP-IVO Specifications |
| RGB VIDEO INPUT |
| Connector |
1-HD-15 female connector |
| Signal Type |
1 RGBHV, RGBS, RGsB, RsGsBs,Component, S-video or Composite |
| Maximum Resolution |
1920 X 1080 (1080P) |
| Impedance |
75Ω |
| Level (nominal) |
Analog 0.7V p-p |
| Level (maximum) |
+-1.0 V |
| RGB VIDEO OUTPUT |
| Connector |
1-HD-15 female connector (Brick models have an additional HD-15 loopback connector) |
| Signal Type |
Same as input |
| Gain |
Unity |
| Impedance |
75Ω |
| Sync output |
5V into Hi Z, 2.2V into 75Ω |
| AUDIO INPUT |
| Connector |
1-3.5 mm stereo mini jack (wallplates), 3 pin Phoenix plug (bricks) |
| Signal type |
Stereo unbalanced |
| Level (nominal) |
0.25V RMS -10dBm |
| Level (maximum) |
1.1V RMS, +3dBm |
| Impedance |
50 kΩ |
| Encoding |
Full stereo 24 bit, 96kHz sample rate |
| Frequency response |
20Hz-15kHz +-0.5dB |
| AUDIO OUTPUT |
| Connector |
Wallplate model receivers 2 RCA jack connectors |
| Brick model |
receivers 3 pin pluggable screw terminals |
| Signal type |
Stereo unbalanced |
| Impedance |
50Ω (Intended to drive a 600Ω or greater load) |
| Gain |
Unity +- 1.5dB |
| CONTROL ADJUSTMENTS |
| Delay Adjust |
Independent for R, G and B delay (Skew models only) |
| Delay range |
0-62 ns (Skew models only) |
| Video Boost Switch |
Dip switch (OFF 0-800’/ON 200-1000’) |
| Gain control |
Manual combined control for RGB |
| RS-232 DATA INPUT |
| Number/Type |
One DB-9 female connector. (4 pin Phoenix plug on brick models) DCE type connection for direct connection to a PC serial port included on two gang transmitters only. Must order TPRO-Serial DB-9 accessory harness for one gang transmitters. |
| Handshaking |
Local loopback only (Models with DB-9 connectors only) |
| RS-232 type |
Unidirectional (data transmission from transmitter to receiver only) |
| RS-232 DATA OUTPUT |
| Number/Type |
One DB-9 male connector. DTE type connection for direct connection to peripheral. |
| Data Rate |
0-19.2k baud |
| INFRARED INPUT |
| Number/Type |
Both models have internal sensor logically OR’d with hardwired input. |
| T-PRO TX brick models |
One 4 pin pluggable Phoenix connector |
| T-PRO-TX wallplate models |
One C-grid SL 5-pin connector on the back of the unit. |
| Compatibility |
Compatible with most IR outputs designed to drive an IR emitter LED. |
| INFRARED OUTPUT |
| Number/Type |
One3.5 mm mini jack, center positive. All TPRO-RX models (Use FSR IR-EC1-6 single or IR-EC2-6 dual emitter accessory.) |
| Output Switch |
Dip switch (Normal 12 mW/High 60mW) |
| Carrier Range |
40 kHz, custom frequencies available per request. |
| POWER REQUIREMENTS |
| TPRO-RX Receivers |
24VDC@0.12A (Skew models are 24VDC@0.19A) |
| TPRO-TX Transmitters |
24VDC@0.09A/Power supplies are optional. Use FSR PS-24DC-500MA |
| GENERAL |
| UTP cable wiring standard/ type |
EIA / TIA-568B CAT5, 5E, 6 |
| Recommended transmission range |
0-1000 ft with a single power supply (Up to 600’ when powered at transmitter. Up to 1000’ when powered at receiver. When using a TPRO-HUB with included power supply: The maximum distance to a transmitter is 1000’. The maximum distance to a receiver is 600’ * A distance of up to 1000’ can be achieved by adding an additional power supply at the receiver |