| Rated power |
- Bridge 4 ohms: 1960W @ 1kHz 1% T.H.D.
- Bridge 8 ohms: 1160W @ 1kHz 1% T.H.D.
- 2 x 2 ohms: 980W per channel @ 1kHz 1% T.H.D. both channels driven
- 2 x 4 ohms: 540W per channel @ 1kHz at <0.1% T.H.D. both channels driven
- 2 x 8 ohms: 275W per channel @ 1kHz at <0.1% T.H.D. both channels driven
- 1 x 2 ohms: 1050W @ 1kHz at <0.1% T.H.D.
- 1 x 4 ohms: 600W @ 1kHz at <0.1% T.H.D.
- 1 x 8 ohms: 290W @ 1kHz at <0.1% T.H.D.
|
| Minimum load impedance |
|
| Maximum RMS voltage swing |
|
| Frequency response |
- 10Hz-45kHz; 0dB, -3dB @ 1W
|
| T.H.D |
- 2 x 2 ohms: <0.1% @ 800W per channel from 20Hz-10kHz, decreasing to 760W @ 20kHz
- 2 x 4 ohms: <0.1% @ 500W per channel from 20Hz-20kHz
- 2 x 8 ohms: <0.1% @ 270W per channel from 20Hz-20kHz
|
| Input CMRR |
|
| Voltage gain |
|
| Crossover |
- 100Hz switchable 2nd order high pass and 3rd order low pass per channel
|
| Crosstalk |
- >-70dB @ 1kHz at 100W power @ 4 ohms
|
| Hum and noise |
- >-100dB, "A" weighted referenced to rated power @ 4 ohms
|
| Slew rate |
|
| Damping factor (8 ohms) |
- >250:1 @ 20Hz-1kHz @ 8 ohms
|
| Phase response |
- +6 to -70º from 20Hz-20kHz
|
| Input sensitivity |
- 0.775V ±3% for 1kHz 4 ohm rated power
- 0.735V ± 3% for 1kHz 2 ohm rated power
|
| Input impedance |
- 15k ohms balanced 7.5k ohms unbalanced
-
|
| Current draw |
- @ 1/8 power:
- 620W @ 2 ohms
- 390W @ 4 ohms
- 250W @ 8 ohms
- @ 1/3 power:
- 1250W @ 2 ohms
- 810W @ 4 ohms
- 460W @ 8 ohms
|
| Cooling |
- Temperature dependent variable speed 80mm DC fan
|
| Controls |
- 2 front panel attenuators
- Crossover select switch for H.P.F, Normal and L.P.F
- Input mode switch for Stereo, Bridge and Parallel
|
| Indicator LEDs |
- 2 DDT (ACL clip limiting)
- 2 signal presence
- 2 active status
- 2 temp
- 2 DC protect
|
| Protection |
- Thermal
- DC
- Subsonic
- Incorrect loads
- Under and over voltage
|
| Connectors |
- Inputs:
- Neutrik Dual Combi 1/4" XLR
- Outputs:
- Three Neutrik Speakon connectors for two channels plus common bridge
|
| Construction |
|
| Dimensions |
- (LxWxH) 10.5 x 19 x 3.5" (266 x 482 x 89mm) behind front panel + 0.6" for handle
- 2 RU mounting
|
| Net weight |
|
| Gross weight |
|
| Warranty |
|
Rated power readings made with BW: <10Hz-22kHz. All power measurements made at 120 VAC. 2 ohm power is time limited by circuit breaker. Input power requirements: 120 VAC, 60Hz, 5A.
*Net weight does not include power cord |